How to Flush a Jackson Water Heater

Posted by on Jan 17, 2014 in Water Heater Repair Jackson MS

Ok, so it is not a glamorous water heater upkeep task, but it does need a little cleaning up from time to time. Yes, today Water Heater Repair Jackson MS is going to instruct one on the best ways to eliminate a water heater. Some recommend doing so as soon as each to three years, we feel it is best to do so as soon as a year. Doing this is not a tough or time consuming task – heck, let the children provide a hand even.

Why Flush a Jackson MS Water Heater?

If it is last the advised life expectancy of the unit, it should have some type of routine flushing done. Doing this will clearly aide in having it run as successfully as possible, which likewise indicates conserving money on the expense of running the darn thing. That alone ought to be a sufficient reason we feel!

In regards to water heater maintenance, flushing it will get free of the buildup of mineral deposits that natural takes place inside the water tank. If one has actually ever had loud sounds, popping, gurgling, mini-explosion noises, that is a sign that there is too much sediment inside the tank. This flushing process will help see to it that the tank heats up water much more quietly.

Step 1. If it is an electric water heater, turn the power off in the main electric breaker box and turn the cold water supply off. If it is a gas heater, it is ok to leave the gas on – simply turn the water off. Though, turn the thermostat setting dial to the pilot setting (make a note to remember what it was initially set at though for later on). Then, whichever faucet the water heater supplies is closest has to be opened. This is typically much easier than opening the pressure relief valve, however one can do that instead.Water Heater Repair Jackson MS

Step 2. At the bottom of the water heater is a drain valve that a yard watering hose can be attached to. There might be a cover over it depending on the maker. Think about turning the heat to the pilot setting a number of hours before flushing it if one desires so the water isn’t going to be as hot when it is drained. If that is not an alternative that’s fine, simply see to it the yard hose made use of is in excellent shape to withstand the higher temperature water.

Run the hose outside away from the house or if the water has already cooled, one can drain the tank into containers.

Step 3. Open the water heater’s drain valve and begin draining the water. For whatever reason the drain valve is normally made of plastic, so if one has an older water heater (and one that has not been drained since before time began) it might stick a little. Simply beware to not break the plastic (which is why it would be good if the darn thing was NOT made of plastic).Water Heater Repair Jackson

Once the drain valve is open, also open the pressure relief valve on the unit. Water will (a minimum of it ought to if it pressure relief valve is working properly) flow some from it. Try to let is flow stable and not too fast so it stirs up the sediment in the water heater. We want the sediment to drain out the bottom from the hose.

If draining in a container, even if having the hose drain into a bucket beyond the garage or basement where the water heater is located, fill a bucket and let it sit to see if the water is clear or if there is sediment, which will usually look like sand in the bottom of the bucket. Just keep draining it till the water is clear.

Step 4. Close the drain on the bottom of the storage tank and close the pressure relief valve if it is still open.

Step 5. Turn the water supply on once more to fill the tank. As soon as it is full once more, slowing open the pressure relief valve again to get some excess air out of the tank. Then, open a hot water faucet in your house to get much more air out of the system.

Step 6. Let the hot water in the bathtub run until a full stream is streaming out. When that occurs, it is ok to turn the power back on if it is an electric water heater, or reset the temperature level setting for a gas water heater. Undoubtedly, turn the bathtub faucet off. In about 20 minutes, the hot water ought to be heated up once more.

There you go! Water Heater Repair Jackson MS is here to address any concerns you could have. Next take have a look at our post on what to do if one has no hot water.

Enhanced by Zemanta